1100 WOOD INSERT
The 1100 insert is the ready-made solution for smaller stone fireplaces. With its back face at a 45° angle, it offers a wide range of configurations.The floor of its firebox is 2.5 inches deep, allowing greater accumulation of ashes and cleaner use.
The 1100 insert also comes with a powerful 144 CFM blower. You'll be amazed and delighted by the 50,000 BTU/h of heat it provides!
APPLIANCE PERFORMANCE (1)
|Fuel type :||Dry cordwood|
|Recommended heating area (sq.ft.) :()||250-1,400|
|Overall firebox volume :||1.5|
|Maximum burn time : ()||6 h|
|Maximum heat output (dry cordwood) : (2)||50,000 BTU/h (14.6 kW)|
|Overall heat output rate (min. to max.) :(2) (3)||11,000 BTU/h (3.2 kW) to 35,000 BTU/h (10.2 kW)|
|Average overall efficiency (EPA cribs / Douglas fir) :(3)||N.A. (HHV)(4)||N.A. (LHV)(5)|
|Average overall efficiency (dry cordwood) : (3)||70 % (HHV)(4)||75 % (LHV)(5)|
|Optimum efficiency : (6) (7)||75 %|
|Average particulate emissions rate : (8)||2.9 g/h|
|Average CO : (9)||N.A.|
(1) Values are as measured per test method, except for the recommended heating area, firebox volume, maximum burn time and maximum heat output.
() Recommended heating area and maximum burn time may vary subject to location in home, chimney draft,heat loss factors, climate, fuel type and other variables. The recommended heated area for a given appliance is defined by the manufacturer as its capacity to maintain a minimum acceptable temperature in the designated area in case of a power failure.
(2) The maximum heat output (dry cordwood) is based on a loading density varying between 15 lb/ft³ and 20 lb/ft³. Other performances are based on a fuel load prescribed by the standard. The specified loading density varies between 7 lb/ft³ and 12 lb/ft³. The moisture content is between 19% and 25%.
(3) As measured per CSA B415.1-10 stack loss method.
(4) Higher Heating Value of the fuel.
(5) Lower Heating Value of the fuel.
(6) Performances based on a fuel load prescribed by the standard at 7 lb/ft³ and with a moisture content between 19% and 25%.
(7) Optimum overall efficiency at a specific burn rate (LHV).
(8) This appliance is officially tested and certified by an independent agency.
(9) Carbon monoxyde.
|High-efficiency EPA certified appliance||Yes, EPA 2020 approved|
|Maximum log length||17”|
|Log positioning||Over width|
|Flue outlet diameter||6"|
|Type of chimney||Liner - ULC-S635, CAN/ULC-S640, UL1777|
|Minimum chimney height (feet)||15'|
|Approved for a mobile home installation||No|
|Shipping Weight||297 lb (135 kg)|
|Door type||Single, glass with cast iron frame|
|Glass type||Ceramic glass|
|Glass surface – dimensions (Width X Height)||15 3/4" x 9 3/8"|
|Glass air-wash system||Yes|
|Premium quality blower included (CFM)||144|
|Overall dimension (Height)||21 1/8"|
|Overall dimension (Width)||25 1/2”|
|Overall dimension (Depth)||22 1/2"|
|Door opening – dimension (Height)||8 3/8"|
|Door opening - dimension (Width)||15 5/8”|
|Firebox – dimension (Height)||11 1/2"|
|Firebox – dimension (Width)||18 1/8|
|Firebox – dimension (Depth)||12 5/8”|
|Firebox lined with refractory bricks for better heat distribution||Yes|
|Stainless-steel secondary-air system improving gas combustion||Yes|
|Adjustable threaded legs||Yes|
|Steel thickness – body||3/16"|
|Steel thickness – top||3/16"|
|Fireplace opening – minimum (Height)||21 3/4"|
|Fireplace opening – minimum (Width)||26"|
|Fireplace opening – minimum (Depth)||12 7/8"|
|USA standard (emissions)||EPA|
|Canadian Standard (emissions)||CSA B415.1-10|
|USA standard (safety)||UL 1482, UL 737|
|Canadian standard (safety)||ULC-S628|
|Tested and listed as per applicable standards||By an accredited laboratory (CAN/USA)|
|Combustion chamber (welds only) and cast iron door frame.||Lifetime||5 years|
|Ceramic glass**, plating (manufacturing defect**), and convector air-mate.||Lifetime||N/A|
|Surrounds, heat shields, ash drawer, steel legs, pedestal, trims (aluminum extrusions), C-Cast baffle**, vermiculite baffle**, secondary air tubes**, removable stainless steel combustion chamber, deflectors, and supports.||7 years||N/A|
|Handle assembly, glass retainers and air control mechanism.||5 years||3 years|
|Removable carbon steel combustion chamber components.||5 years||N/A|
|Standard and optional blower, heat sensors, switches, rheostat, wiring, and electronics.||2 years||1 year|
|Paint (peeling**), gaskets, insulation, ceramic fiber blankets, firebricks, and other options.||1 year||N/A|
|All parts replaced under the warranty.||90 days||N/A|